How KESS3 Clone DCM6.2C Engine from Peugeot Boxer 2015?

 

In this article, we will show you how to clone DCM6.2C using Alientech KESS3.

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-1

Vehicle:

Peugeot Boxer 2015


Module:

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-2

Steps:

Select Peugeot-- Boxer II (2015)-- 2.0BlueHDi 130 96-- Delphi DCM6.2C.

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-3

Check out BOOT mode pinout and connect KESS3.

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-4

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-5

Identify ECU.

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-6

Read and backup ECU data.

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-7

Swap to new module.

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-8

Write data.

how-kess3-clone-dcm6.2c-engine-from-peugeot-boxer-2015-9

Done! Simple and Nice!

http://blog.cardiagtool.co.uk/how-kess3-clone-dcm6-2c-engine-from-peugeot-boxer-2015/

评论

发表评论

此博客中的热门博文

Solved! Fetrotech Read Mercedes EDC16CP31 "S1 and S2 pinout error"

图片
  Question: EDC16CP31 doesn't work on Fetrotech Silver you have three tries with three different cars and all three don't work put X on MB 16cp31. 1-b class not work 2-e class not work 3-sprinter not work Here we have 3 different pinouts of EDC16CP31: PINOUT 1 (on Fetrotech ) PIN33 T96 - GPT0 PIN34 T96 - GPT1 PIN2 T58 - GND PIN5&41 T58 - +12V PIN43 T58 - KLINE PINOUT 2 PIN33 - GPT0 PIN77 - GPT1 PIN2- GND PIN5&41 - +12V PIN43 - KLINE PINOUT 3 PIN86 - GPT0 PIN77 - GPT1 PIN2- GND PIN5&41 - +12V PIN43 - KLINE Through tests, PINOUT2 works, and CAN-H/-L is not required. http://blog.cardiagtool.co.uk/solved-fetrotech-read-mercedes-edc16cp31-s1-and-s2-pinout-error
阅读全文

Free Download GODIAG J2534 Cable Driver and Software

图片
  GODIAG J2534 Cable , compatible with J2534 Passthru and ELM327, can work with HDS, TIS, JLR SDD, PCMflash, FORSCAN... Free Download GODIAG J2534 Software from Cardiagtool : GODIAG J2534 Driver VAG ODIS 9.10 Toyota 17.00.00/17.20.013 HDS HONDA 3.104.024 JLR SDD 163 Forscan 2.3.48 Scanmaster v2.1 PCMflash (*Install GODIAG J2534 driver first) How to Install Software?     Test with JLR SDD V163: To install driver, run "GODIAG DriverSetup_vc_xc86_1v0". Connect GODIAG VNCI to Land Rover Freelander 2 Open "JLR SDD". Go to Computer Management>>Device Manager>>Port (COM & LPT) Check if VCI is connected. Input VIN to enter. Go to Diagnosis>>Powertrain>>Engine system>>Engine cooling>>Coolant contamination View PCM DTC. http://blog.cardiagtool.co.uk/free-download-godiag-j2534-cable-driver-and-software/
阅读全文

Original FoxFlash Read MED9.1 on Bench Tips

图片
Question: MED9.1 on bench will not connect. Bench box with stable PSU, and tried all pinouts but FoxFlash Tool will not read ECU. Solution: Step 1. Disconnect BDM Adapter!! put 12V in FoxFlas h not bench box After that, both MED9.1 still fail. Step 2. Use correct cable to connect, the white cable with red stripes is J1708 cable. Feedback: My problem is fixed. The ECU connects. http://blog.cardiagtool.co.uk/solved-foxflash-fail-to-connect-med9-1-on-bench/  https://www.foxflash.co.uk/ 
阅读全文