KT200 Read Old EDC16C34 in BDM No Welding Success

 

This is a review of KT200 on old EDC16C34:

Reading an old edc16c34 calculator in bdm with ktag bosch adapter to avoid welding.

Eeprom/Flash reading ok.

kt200-read-old-edc16c34-in-bdm-no-welding-success-1

kt200-read-old-edc16c34-in-bdm-no-welding-success-2

Writing egr off automatic cheksum calculation.

Check cheksum written file with perfect Lsuite

kt200-read-old-edc16c34-in-bdm-no-welding-success-3


Good to Know:

Try and find shorter cables, as with BDM these need to be as short as possible. We can purchase easily online, just count number of cables on ribbon. The shorter means less chance of data Error.

e.g. short one, the galletto one

kt200-read-old-edc16c34-in-bdm-no-welding-success-4

Besides, we can also make small start to place KT200 Hardware above our bdm holder


http://blog.cardiagtool.co.uk/kt200-read-old-edc16c34-in-bdm-no-welding-success/

评论

发表评论

此博客中的热门博文

Solved! Fetrotech Read Mercedes EDC16CP31 "S1 and S2 pinout error"

图片
  Question: EDC16CP31 doesn't work on Fetrotech Silver you have three tries with three different cars and all three don't work put X on MB 16cp31. 1-b class not work 2-e class not work 3-sprinter not work Here we have 3 different pinouts of EDC16CP31: PINOUT 1 (on Fetrotech ) PIN33 T96 - GPT0 PIN34 T96 - GPT1 PIN2 T58 - GND PIN5&41 T58 - +12V PIN43 T58 - KLINE PINOUT 2 PIN33 - GPT0 PIN77 - GPT1 PIN2- GND PIN5&41 - +12V PIN43 - KLINE PINOUT 3 PIN86 - GPT0 PIN77 - GPT1 PIN2- GND PIN5&41 - +12V PIN43 - KLINE Through tests, PINOUT2 works, and CAN-H/-L is not required. http://blog.cardiagtool.co.uk/solved-fetrotech-read-mercedes-edc16cp31-s1-and-s2-pinout-error
阅读全文

Free Download GODIAG J2534 Cable Driver and Software

图片
  GODIAG J2534 Cable , compatible with J2534 Passthru and ELM327, can work with HDS, TIS, JLR SDD, PCMflash, FORSCAN... Free Download GODIAG J2534 Software from Cardiagtool : GODIAG J2534 Driver VAG ODIS 9.10 Toyota 17.00.00/17.20.013 HDS HONDA 3.104.024 JLR SDD 163 Forscan 2.3.48 Scanmaster v2.1 PCMflash (*Install GODIAG J2534 driver first) How to Install Software?     Test with JLR SDD V163: To install driver, run "GODIAG DriverSetup_vc_xc86_1v0". Connect GODIAG VNCI to Land Rover Freelander 2 Open "JLR SDD". Go to Computer Management>>Device Manager>>Port (COM & LPT) Check if VCI is connected. Input VIN to enter. Go to Diagnosis>>Powertrain>>Engine system>>Engine cooling>>Coolant contamination View PCM DTC. http://blog.cardiagtool.co.uk/free-download-godiag-j2534-cable-driver-and-software/
阅读全文

Original FoxFlash Read MED9.1 on Bench Tips

图片
Question: MED9.1 on bench will not connect. Bench box with stable PSU, and tried all pinouts but FoxFlash Tool will not read ECU. Solution: Step 1. Disconnect BDM Adapter!! put 12V in FoxFlas h not bench box After that, both MED9.1 still fail. Step 2. Use correct cable to connect, the white cable with red stripes is J1708 cable. Feedback: My problem is fixed. The ECU connects. http://blog.cardiagtool.co.uk/solved-foxflash-fail-to-connect-med9-1-on-bench/  https://www.foxflash.co.uk/ 
阅读全文