博文

目前显示的是 十一月, 2022的博文

Is BDM CMD/Alien Adapter Compatible with FoxFlash BDM Mode?

图片
  Some customers wondered if their BDM adapters are compatible with FoxFlash BDM mode. Here Cardiagtool tech Answer: Any BDM probe compatible with original DFox Tool will work. BDM adapters cannot use generic adapters such as the cheap Ktag type. It can only use adapters designed for the following original products - Dfox, EVC BDM100, FG_TECH, AMT. Other BDM types will damage your ECU/ FoxFlash Hardware . http://blog.cardiagtool.co.uk/is-bdm-cmdalien-adapter-compatible-with-foxflash-bdm-mode/

How does FoxFlash Work for Agriculture?

图片
  One customer asked how does FoxFlash Tool work for agriculture. On Kess/ new Genius it is needed adapters to work on OBD truck tractor. Here Cardiagtool Technician Answer: A lot of Agriculture is Bench and most new Agriculture use standard OBD connection For old model without OBII port, adapters are not needed. e.g. Mercedes Truck -2004 Mercedes Truck with 38pin port Volvo Truck http://blog.cardiagtool.co.uk/how-does-foxflash-work-for-agriculture/

KT200 Possible to Read SIM32 on Bench by OBD with Godiag Cable?

图片
  Question: Can KT200 Tool read on the table by obd with godiac cable calculator Sim32 Clio 3 1.2? Answer: Test, if not work, do gateway/ immo clearance. KT200 only support SIM32 on BDM/ JTAG mode. ECU Numbers List: Car List: Siemens SIM32 Bench Pinout: Try to read it with Godiag Breakout Box and Full-protocol Cable. Siemens SIM32 JTAG Pinout: Kit to use: - Multifunction cable - Flat cable - 1 resistance 320Ω Driver to Read: - BDM / JTAG MODE - JTAG RENESAS - AUD SH xxxxx Driver to Write: - TOOL BOOT - RENESAS - SH xxxxx BOOT MODE http://blog.cardiagtool.co.uk/kt200-possible-to-read-sim32-clio3-1-2-on-bench-by-obd-with-godiag-cable/

KT200 Possible to Read Valeo VD46 SH72546R on Bench?

图片
  Question: KT200 Tool can't read that ecu!!! Valeo VD46, possible to read it? Answer: VD46 is different from V46, the processor is SH725 and no driver supports. Difference between VD46 and V46: 1.VD46 has only two compartments while V46 has 3. 2.V46 is with SH72544 processor, VD46 is with SH72546 Other Solutions: Try JTAG mode with Trasdata Tool. PCB: Direct Connection: For the connection use the cable F32GN037C/D connected to the ECU. Make sure that the POWER led (red) on Trasdata is ON. ECU Connector: JTAG Loose Wires Connection: For the reading & writing procedures use the FLAT cable F34NTF53 Connect the wires on the pads avoiding any short circuits. Connections are required on both sides of the ECU. 1)Processor Side 2)Cover Side Review: VD46 will not support due to SH72546R processor. I use Trasdata 11 http://blog.cardiagtool.co.uk/kt200-possible-to-read-valeo-vd46-sh72546r-on-bench/

KT200 Read Old EDC16C34 in BDM No Welding Success

图片
  This is a review of KT200 on old EDC16C34: Reading an old edc16c34 calculator in bdm with ktag bosch adapter to avoid welding. Eeprom/Flash reading ok. Writing egr off automatic cheksum calculation. Check cheksum written file with perfect Lsuite Good to Know: Try and find shorter cables, as with BDM these need to be as short as possible. We can purchase easily online, just count number of cables on ribbon. The shorter means less chance of data Error. e.g. short one, the galletto one Besides, we can also make small start to place KT200 Hardware above our bdm holder http://blog.cardiagtool.co.uk/kt200-read-old-edc16c34-in-bdm-no-welding-success/

Free Download FoxFlash Software and Installation Guide

图片
  This article is going to share with you the latest software of new chip tuning tool FoxFlash and how to install it. Free Download FoxFlash Software from Cardiagtool : FoxFlash Manager (Main Software: Download via "FoxFlash Manager" after activation) Operating System: Windows 7/ 8/ 8.1/ 10/ 11 PC Requirements: CPU>2.5 GHz (Intel i5, i7) RAM>4G How to Install Software? 1.Download software (manage tool + main software) FoxFlash Manager: above link or official website: https://www.dfb-technology.com/download.html Main Software: Download via "FoxFlash Manager" after activation 2.Run "FoxFlash Manager", register by your email 3.Check SN number on device's back, which is the safe code and the password, so keep it well Enter safe code to activate device 4.Connect FoxFlash Tool to computer by USB cable, and network connection is required. Continue to download main software via Manage Tool 5.After downloading main software, install the drivers Path: C:\Prog...

VW CAN Filter Odometer Correction Instruction

图片
For many new VW cars, we cannot read data from the dashboard via OBD port without VW CAN filter . Note: To use this 35XX CAN filter , dashboard must have LCD module. Support List (Jetta, Santana, Rapid, Polo, Lavida): Type 1 Jetta: 31G 920 850B, 31G 920 850D, 31G 920 850C, 31G 920 850E, 34D 920 850B, 31G 920 850G Gran Santana: 34D 920 Santana: 34D 920 850B, 31G 920 850F Rapid: 32D 920 850B, 31G 920 850H Polo: 6RD 920 860J, 31G 920 850A (special design) Polo: 6RD 920 860G Polo: 6RD 920 860H, 34D 920 850A (special design) Type 2 Santana: 34D 920 850A (special program) Jetta: 31G 920 850A (special program) Type 3 Lavida: 18D 920 860A,  18D 920 850A (special design, two types) Type 4 Lavida: 18D 920 850A, 18D 920 850A (If special design, type3 is supported) Type 5 New Lavida: 18D 920 870A Type 6 870, 870B Type 7 Rapid: 860, 6VD 920 700, 32D 920 860 How to Use? Connect as wiring diagrams. Then plug in power supply and test. After dash displays, cables touch once, number w...

KT200 Fail to Read Honda CRV 2010R EDC17CP16 Password Solution

图片
  Here is a review of V11.01 KT200 : Honda crv 2010r edc17cp16 bench read failed... is possible to read write on bench? Make sure the ECU is CP16 and not EDC17CP06. Pinout for cp06 got different gpt and NOT work at all. EDC17C16 Pinouts: EDC17C06 Pinout: Reason: The ECU has been subject to dealer update so Tprot level has been changed. Review updated: Tried also with flex - same - password reading failed but AutoTuner read it and write perfect. http://blog.cardiagtool.co.uk/kt200-possible-to-read-honda-2010-edc17cp16-password-on-bench/

Free Download V3.0.1 ECUhelp Software

图片
  Here we share the latest ECUhelp software for ECU tuning. This software could work with your ECU Programmers including PCMtuner , KT200 , ECU Bench Tool ... Free Download ECUhelp Software from Cardiagtool : V3.0.1 ECUhelp Wiring Diagram. Download VR Files. Other Free Software: https://www.cardiagtool.co.uk

Fixed! PCMtuner Don't Read Module 71 after Changing Transistors

图片
  Question: PCMtuner V1.27 still won't read module 71 in bench mode, even after changing the transistors. Here is a Possible Solution: Go to "Settings" on PCMtuner 1.27 Program. Disable "Use other GPT outputs pins with PCMtuner hardware". Possible Reason: This GPT option only works on Original Scanmatik as that has 2 extra GTP in case the first 2 fail. http://blog.cardiagtool.co.uk/fixed-pcmtuner-dont-read-module-71-after-changing-transistors/