CardiagtoolUK

  In this article, we are going to show you how to generate diagnostic reports on Launch CRP919 BT. This method applies to Launch CRP919E BT , CRP919X BT , and other Launch Diagnostic Tablet .   Vehicle: Buick GL8 2021   Guidance: 1)Diagnose Turn on CRP919 BT, Intelligent Diagnose>>Diagnostic>>HDQ+HFQ>>Health Report>>   2)Generate Report Select 'Report'. Select 'Other share' or 'QR code sharing' to share reports. Done! Hope this helps! http://blog.cardiagtool.co.uk/how-to-generate-diagnostic-report-on-launch-crp919-bt/

  New OBD VR Protocol for Continental EMS24XX is available on AutoTuner .   Update Info: We are updating our OBD protocol for Continental EMS24xx ECUs installed in Ford and Mustang vehicles. Until now, only virtual reading (VR) was available for these ECUs. This operation has now been replaced with a real reading (NR) directly via the OBD port. This ensures full compatibility, without depending on the availability of the file on our server. Important note: previous virtual reads were 4MB in size, while the new real reads are 3MB . A new read is therefore required before any further operation on these ECUs. Stay tuned to discover our upcoming news! Original AutoTuner: https://www.cardiagtool.co.uk/autotuner-ecu-programmer-master-version.html   Key Features: Type: Engine Control Unit (ECU) Readout: OBD NR MCU: TC1791 Read time: 2min 45sec Write time: 1min 30sec Checksums correction   Compatibility List* FORD: 3.5 V6 / 3.7L Duratec V6 / 5.0 Modular V8 / 6.2 V8...

  Alientech KESS3 V2.23 is available! New OBD VR Protocol for Bosch MD1CP004 is ready. Make sure KESS3 CAR LCV OBD Protocol is activated on your tools. Update Info: This update completes the existing BENCH coverage available on KESS3, offering an even more immediate solution by allowing direct access through the diagnostic port—no ECU disassembly required. A practical solution to improve daily operational efficiency. It’s not just about performance: the speed and effectiveness of the OBD VR mode also prove extremely useful for repair and maintenance on sensitive components prone to wear or malfunctions—often responsible for warning lights and reduced performance. Fast and targeted interventions truly make a difference in the workshop. Check compatibility and take advantage of the new coverage: Audi – 3.0 TDI Euro 6 Volkswagen – 3.0 TDI Euro 6   Buy Original KESS3 here: https://www.cardiagtool.co.uk/original-kess-v3-ecu-programmer.htmlhttps://www.cardiagtool.co.uk/original...

  Problem: Xhorse Bluetooth Digital Smart Key "This device not allowed to be used in the current region". Here is the Reason: This key is CN version, so it won't work outside China.   Solution: 1.Reset device Press and hold 20s. 2.Connect to device by iPhone After all operations, make sure device shown GL version (Path: Settings>>Update) 3.Reset device again, connect device by Android phone   Done! http://blog.cardiagtool.co.uk/xhorse-bluetooth-digital-smart-key-not-allowed-to-be-used-solution/

  Yanhua ACDP Module 38 is designed for BMW G-Series BDC2 Add Key. Here we will show you how to use the new module. Step-by-step Guidance: 1.Untighten the screw 2.Find marked columns 3.Align column with marked holes 4.Slightly press module 38 to tighten it 5.Tighten the screw 6.Open BDC2 module. 7.Untighten the screw 8.Remove module 38 Done! That's how to use Yanhua ACDP Module 38 for BMW G-Series Add Key . http://blog.cardiagtool.co.uk/how-to-use-yanhua-acdp-module-38-for-bmw-g-series-bdc2-add-key/

  Alientech KESS3 V2.22 is updated! New BOOT protocols for Weichai and Kubota are available. Update Info: Work in BOOT mode*, operating with the ECU open, on the Weichai ECU13 WISE15 units used in the 3.2L Weichai engines installed on the 2022 Dongfeng LX2004 machines, and on the Bosch REXROTH RC12-10/30 ECUs installed on the 6.1L Kubota engines of the Kubota M2003 Series tractors produced since 2021. This update provides full support for both control units, giving you a real operational advantage: be the first to intervene with KESS3 and stay ahead of the competition. Optimize engine performance parameters, improve overall efficiency, and address all the critical issues that limit productivity in the field or on site. Check compatibility with the now-supported vehicles and ECUs: Dongfeng – LX2004 3.2L Kubota – M2003 Series 6.1L   *Working in BOOT mode with KESS3 means operating directly on the ECU’s electronic board: a precise bench intervention that allows you to work with...

  Check out the latest updates of immobilizer functions on OBDSTAR Tools . Some functions require OBDSTAR RH850 AKL Adapter Kit and are only available on OBDSTAR X300 Classic G3 . Update Info:   VW/AUDI/SEAT/SKODA V45.49 Details Added Add key programming function (supported AKL) for VW/AUDI/SEAT/SKODA MQB48-5A keys, which supports online synchronization code calculation. (Need to use with RH850/V850 Adapter Kit )   Add read IMMO data function (all keys lost) for VW/AUDI/SEAT/SKODA IMMO IV NEC24C64 and NEC24C32 dashboards by BENCH, without removing IC, soldering PCB and making server data. (Need to use with VW4-AKL Cable )   Details Optimized Optimized software.   NISSAN/INFINITI/ENUCIA/VENUCIA V42.69 Details Added Add PROXIMITY All Keys Lost, PinCode Read by C4-06 for below models: NISSAN ARIYA 2012- NISSAN PATHFINDER AUSTRALIA 2022 NISSAN PATHFINDER EUROPE 2022 NISSAN PATHFINDER NORTH AMERICA 2022 NISSAN ROGUE NORTH AMERICA 2021- NISSAN ROGUE SOUTH AMERICA 202...

  New OBD protocols are available on AutoTuner . New updates cover Bosch EDC17C06, EDC17C41, EDC17C50, EDC17C56, EDC17CP02, EDC17CP09, EDC17CP45, and EDC17CP49. We are proud to announce the very first protocol release for your AutoTuner One . Bosch ECUs   EDC17C06 , EDC17C41 , EDC17C50 , EDC17C56 , EDC17CP02 , EDC17CP09 , EDC17CP45 , and EDC17CP49 are now supported for Alpina , BMW , and Mini vehicles, covering both E-Series and F-Series. You benefit from full coverage of diesel engines, ranging from the 1.5L 16d to the 3.0L 50d M, featured across many of BMW Group’s flagship models. These protocols have been carefully adapted to ensure optimal robustness, delivering a smooth and reliable user experience Buy AutoTuner here: https://www.cardiagtool.co.uk/autotuner-ecu-programmer-master-version.html   Key Features: Type: Engine Control Unit (ECU) Readout: OBD VR MCUs: TC1766, TC1796, TC1797 Write time with unlocking: 6min to 8min Write time once unlocked: 1min to 2min Che...

  In this article, we are going to show you how to repair KM on MB HU6 ODO module.   Tools: Yanhua ACDP Module 37 HU6 YH-OBD Platform   Steps: Run ACDP phone app. Connect app to ACDP/ ACDPII Programmer via Bluetooth. Select Benz>>HU6 ODO Module (IC177) mileage correction>>R7F701403 (A167/A213/A247) Connect ACDPII to vehicle. Select 'OBD identify'. Check VIN and KM. Select OBD+ICP reset mileage>>Original module reset mileage Select 'Step 1: OBD backup data'. Remove MB HU6 cluster module. Select 'Help' beside Step 2. Connect ACDP to MB HU6 unit as required. Select 'Step 2: ICP modify data'. Install back MB HU6 unit. Connect ACDP to vehicle. Select 'Step 3: OBD modify KM'. Check if KM is zero. Enter KM. Done! That's how repair KM on MB HU6 ODO Module (IC177) by ACDP Module 37 . http://blog.cardiagtool.co.uk/mb-hu6-odo-module-ic177-km-repair-using-acdp-module-37/

  ID48 96bits Copy Function on CGDI K2 is available on April 19th. So, here we are going to show you how to use this function. How to Clone ID48 96bit chip? Run CGDI K2 app. Select 'Chip Identification Copy'. Put key or chip on key coil. Select 'Chip Identification'. Chip can be cloned. Select Decoded Copy>>48 (96bit) online calculation ID48 cloning guidance. Select 'Query Last Result'. Put working key into coil and tool will recognize it. Take out working key and put aftermarket ID48 chip into coil for cloning. New chip turns on cluster without problems. Done! That's how to use ID48 cloning function on CGDI K2 Key Tool . http://blog.cardiagtool.co.uk/how-to-clone-id48-96bit-chip-using-cgdi-k2/

  APPRO2 is a professional tool for key programming and odometer correction. Here we are going to show you how to correct CAS4+ odometer via OBD using this tool.   Guidance: Connect APPRO2 to BMW. Select Car Models>>BMW>>CAS4/CAS4+ [0042] Connect vehicle. Back up coding. Preprocess ECU. Read key info. Read ISN by working key. Mileage reset. Put key in coil in APPRO2. Select 'ReadkeyinDev'. Select 'FixKeyMilage' and input new mileage. Done! That's how to repair CAS4+ mileage via OBD using APPRO2 Tool . http://blog.cardiagtool.co.uk/appro2-bmw-cas4-obd-odometer-correction/